MotionShop.com - Motion Control


Custom Search


Motion Control Air Bearing Stages from H2W Technologies

H2W Technologies Air Bearing Stages Overview

H2W Logo
Visit our Website
You Tube
Visit our Blog

Santa Clarita, CA —-- Motion Control - The ABS positioning stage is a high precision, granite base, air bearing positioning stage for high end positioning applications. . It is driven by an ironless core, non-cogging 3 phase brushless linear motor and guided by 5 flat magnetically preloaded air bearings floating on a granite base.

The ironless core coil assembly is used as the drive mechanism for the AB stage because of its smooth, non-cogging operation. The lightweight of the coil and table assembly allows for high acceleration of light loads.

The air bearings, which are used for supporting and guiding the payload, float on a cushion of air. This ensures that there are no wearing components in the system. The air bearings are not limited to acceleration limits like their mechanical counterparts where balls and rollers can slide instead of roll at high accelerations.

The stiff cross section of the granite base of the stage ensures a flat straight stable platform for the payload to ride on and does not require any special mounting considerations.

Bellows (folded way covers) with a 12:1 extension to compression ratio may be added to an ABS stage.

The power for the moving 3 phase coil assembly, encoder and limit switches is routed through shielded flat ribbon cable. Special consideration was made to separate the power and signal cables from each other to reduce the effects of noise on the system. The power cable for the coil assembly and a vacant cable for the customers payload power usage are installed on one side of the stage and the encoder signal, limit switch and an additional vacant signal cable for the customers payload signal usage is provided on the other side of the stage. Standard connectors are provided.

The ABS positioning stage incorporates the latest in linear motion technology:

Motors: Non-contact 3 Phase Brushless Linear Motor, Ironless Core, commutated either sinusoidally or trapezoidally with Hall Effects. The encapsulated coil assembly moves and the multi pole permanent magnet assembly is stationary. The lightweight coil assembly allows for higher acceleration of light payloads.

Bearings: Linear guidance is achieved by using magnetically preloaded, porous carbon or ceramic air bearings; 3 on the top surface and 2 on the side surface. The bearings are mounted on spherical surfaces. Clean, dry filtered air must be supplied to the moving table of the ABS stage.

Encoders: Non-contact glass or metal scale optical linear encoders with a reference mark for homing. Multiple reference marks are available and are spaced every 50 mm down the length of the scale. Typical encoder output is A and B square wave signals but sinusoidal output is available as an option.

Limit Switches: End of travel limit switches are included at both ends of the stroke. The switches can be either active high (5V to 24V) or active low. The switches can be used to shut down the amplifier or to signal the controller that an error has occurred. The limit switches are typically an integral part of the encoder, but can be mounted separately if required.

Cable Carriers: Cable guidance is achieved by using flat, shielded ribbon cable. Two additional unused shielded flat ribbon cables are supplied for customer usage with the stage. The 2 power cables for the stage and customer payload are installed on one side of the stage and the 2 signal cables for encoder, limit switch and customer payload are installed separately on the of the stage.

Bellows: The ABS comes standard with neoprene / nylon bellows with Mylar stiffeners.

Hard Stops: Hard stops are incorporated into the ends of the stage to prevent over travel damage in the event of servo system failure.

Advantages:

  • Excellent flatness and straightness specifications
  • Lowest velocity ripple
  • No wearing parts
  • Enclosed with bellows

Applications:

  • Pick and Place
  • Vision Inspection
  • Parts transfer
  • Clean room

Stages can be ordered for any stroke up to 80 inches and any continuous force up to 24 lbs. The stages are built as the orders are placed, they are not stocked, as each customer requirement is different.

About H2W Technologies, Inc.

H2W Technologies, Inc. is dedicated to the design and manufacture of linear and rotary motion products that are used in the motion control industry. The complete line of linear electric motors includes: Single and dual axis linear steppers, DC brush and brushless linear motors, voice coil actuators, and AC induction motors. Also offered is a complete line of ball screw, lead screw and belt driven positioning stages.

Other motion control products include: Limited angle torque motors for compact, limited angular excursion rotary servo applications, 3 phase brushless rotary servo motors with matching digital servo amplifiers and permanent magnet linear brakes for fail-safe, zero power braking for baggage handling and people moving applications as well as amusement park rides.

With over 75 years combined experience in the linear and rotary motion field, the H2W Technologies team of engineers offers the optimal solution to the most demanding motion control, requirements.

To see all of H2W Technologies' Products and Application Stories featured on MotionShop.com, enter h2w in the Google custom search box (upper left, above)

For additional information contact Mark Wilson at H2W Technologies, 26380 Ferry Ct, Santa Clarita, CA 91350; Tel: 888-702-0540, Fax: 661-251-2067, E-Mail: info@h2wtech.com or visit the website at http://www.h2wtech.com


For other Motion Control Components, Applications, and Technology from H2W Technologies, Inc. go to: the H2W Technologies Blog - http://LinearMotionBlogger.com



Add Your Product/Company | Need a Website? | Need a Product Release?
motioncontrolmktg@gmail.com

"MotionShop.com", "The Motion Control Home Page", and "Motion Control Archive" are trademarks of E-Media Publishing. Other product and company names are trademarks or registered trademarks of their respective holders.

Copyright © 1997-2019 E-Media Publishing - Motion Control Marketing